Here You can Take A Free NACE CIP Level 1 Exam Practice Test, with Latest NACE (CIP) Coating Inspector Program Level 1 Question and Answers
1.
Corrosion will generally NOT occur on a steel substrate when
2.
Inert gases may be placed in confined spaces to reduce or prevent corrosion.
3.
New steel is not hom*ogenous and contains
4.
Carbon steel will generally corrode if it is electrically connected in the presence of a suitable electrolyte with
5.
Which of the following is anodic with respect to carbon steel when in a seawater electrolyte?
6.
Chemical salts dissolved in an electrolyte generally contribute to corrosion by
7.
The rate of corrosion occurring at a hole, scratch, or other discontinuity of a coating film may be affected by I. the presence of an electrolyte II. adherent mill scale on the substrate III. the anode is in contact with the atmosphere
8.
The use of an incorrect thinner may cause a coating to
9.
Coatings can control corrosion of steel by I. preventing electrolytes from contacting the metal surface. II. sacrificing themselves to protect the steel substrate. III. supplying inhibitors to passivate the metal surface.
10.
The vehicle of a coating consists of I. solvent, binder, and liquid additives. II. solvent only. III. binder and pigment.
11.
Inspection reports should address the
12.
A typical daily report will include I. description of equipment and manpower. II. explanation of work stoppages. III. ambient conditions. IV. inspector’s opinion of the contractor.
13.
The required sequence of work within a specification on a project is
14.
Solvents are added to coating formulations to
15.
Most organic coatings are
16.
Inspection reports should include which of the following? I. Environmental conditions II. Details of surface cleaning and materials III. Coatings application
17.
Which items are the basic principles in documentation by the inspector? I. Reports are written in ink II. No blank spaces III. Reports should be signed IV. Reports must be printed
18.
Inspector’s daily reports are used for which of the following? I. By the contractor to estimate the amount of work done that day II. To provide continuity between inspectors. III. To aid in arbitration between the contractor and client IV. To help in cases of a coating failure
19.
A pre-job conference is helpful for reviewing I. safety procedures. II. cleaning operations. III. application procedures.
20.
The inspector’s method of marking defects
21.
In case of conflict or a difference of opinion, the coating inspector needs to
22.
All bidders on a coating job should I. attend the pre-bid meeting. II. be given a copy of the pre-job minutes. III. attend the pre-job conference. IV. be allowed a walk-through of the project.
23.
Before attending a pre-job conference, the coating inspector should I. read and understand the specification. II. identify problems with the specification. III. walk through the work site.
24.
The coating contractor’s questions about enforcing the coating specification should best be brought up
25.
The coating inspector should act as a recording secretary during the pre-job meeting.
Steel surface temperature during coating application should be
28.
Dew point is measured and calculated by using
29.
The Dew point is the temperature at which
30.
A decrease in temperature will generally cause the corrosion rate to I. increase. II. decrease. III. remain constant.
31.
The presence of certain salt deposits such as ferrous sulfate or ferrous hydroxides may be determined by which of the following?
32.
Workers exposed to hazardous levels of free silica dust such as released during the sandblast cleaning process may develop silicosis, which is a disease of the
33.
ISO 8503-1 comparator are available for which of the following abrasives? I. Sand II. Grit III. Shot
34.
Which of the following statements concerning ultra-high pressure water jetting is true? I. Production rates are cost-effective. II. Seldom used for surface preparation. III. Often used for surface preparation. IV. Lower pressure will not remove the tight mill scale.
35.
Coating operations should NOT take place unless the substrate surface temperature is At least
36.
The cathode of a corrosion cell
37.
Nozzle pressure for manual blast cleaning is generally accepted to be
38.
Extra-coarse Testex replica tape is used when it is expected that the depth of the anchor pattern/surface profile to be measured will be 3 mils (75 microns).
39.
When following a specification for surface preparation standards, the inspector should NOT?
40.
If the coating inspector finds that the coating was applied thicker than specified, he/she should
41.
33 feet is approximately how many meters?
42.
The requirements of a project should be defined by the
43.
The coating inspector should require white metal surface preparation if
44.
A well-written coating specification should contain information regarding I. surface preparation standards. II. safety. III. locations to be coated.
45.
If the desired DFT of a coating is 100 microns (4 mils), what wet film thickness will be required if the coating contains 100% volume solids?
46.
It is the coating inspector’s responsibility to
47.
The coating inspector’s responsibility is to
48.
It is the coating inspector’s responsibility to
49.
The coating inspector’s responsibility is to
50.
Inspection of mixing and thinning operations is important
51.
An inspector’s primary duty is to I. observe the actions of the contractor. II. report actions of the contractor. III. document actions of the contractor. IV. enforce all safety rules.
52.
Corrosion is slower in hot environments than in cool ones.
53.
Accidental injection through the skin by airless spray
54.
If the inspector observes coatings or solvents being applied to a surface, through an air hose, in an Air Spray system he/she should I. look for other signs of poor practice. II. notify the foreman. III. record findings in a log book.
55.
With conventional air spray equipment, the dry spray may be caused by
56.
“Arcing” a spray gun may cause I. uneven application. II. a spark hazard. III. excessive overspray.
57.
Which of the following is an advantage of airless spray compared to conventional air spray?
58.
Always ground the fluid hose used in an airless spray to
59.
The use of respiratory equipment is not necessary when spray painting.
60.
Many liquid coatings
61.
The presence of oil or moisture in compressed air
62.
Conventional air spray guns have adjustments for
63.
According to NACE RP0188-99, the search electrode of a high-voltage holiday detector should be moved across the surface at approximately
64.
According to SSPC-PA 2, always calibrate magnetic DFT (Type 1) gauges
65.
The paint inspection gauge (“Tooke” gauge) is a destructive test instrument.
66.
Generally, applicators do NOT need respirators when spray painting.
67.
Fluid pressure in a conventional air spray fluid line is controlled by
68.
Check for holidays using a
69.
Nondestructive test instruments, properly used
70.
High-voltage DC holiday detectors are used to test
71.
All magnetic DFT instrument magnets or probes must be held at a right angle to the painted surface to produce valid measurements.
72.
Which of the following are the principal advantages of abrasive-injected water blast over water washing? I. Increased profile II. Increased production III. Reduced manpower
73.
There is no spark hazard associated with holiday test equipment.
74.
Always ground low-voltage DC holiday detectors to
75.
Magnetic DFT instruments
76.
Air temperature has no effect up on relative humidity.
77. Depth of anchor pattern/surface profile will not affect DFT readings.
78.
Where will you find information such as ingredients, exposure limits, and flammability classifications of coatings?
79.
Which items of information are generally found on product data sheets? I. Solids by volume II. VOC values III. Chemical composition
80.
Which items found on a product data-sheet provide application information? I. Cure time II. Profile III. Tip size IV. Recoat interval
81.
When applying coatings, instructions regarding appropriate types of Personal Protective Equipment (PPE) will be found within the
82.
The Material Safety Data Sheets (MSDS) I. are not required to be maintained at the job site. II. lists the health hazards of the material. III. lists the protective equipment required during application.
83.
Which of the following is a type of coating defect that occurs when each brush stroke or spray gun pass is visible after the coating has cured?
84.
Osmotic blistering is most likely to occur as a result of
85.
Intercoat delamination may be reduced by
86.
If a coating that cures by chemically-induced polymerization is applied without the converter having been added first the
87.
Chalking
88.
The type of coating that cures by heat-induced polymerization is
89.
Which of the following coating types are often supplied in two components?
90.
Phenolic coatings are very flexible.
91.
Curling or lifting can be caused by I. solvent attacking an existing coating film. II. application of an incompatible coating over an existing coating. III. deterioration of a paint film due to old age.
92.
Chalking is best described as
93.
Failure to add the converter to the base before application of a coating that cures by chemically induced polymerization may result in
94.
To extend the pot-life of an epoxy coating the applicator may
95.
The percentage of metallic zinc dust by weight in the dried film of a zinc-rich coating is generally
96.
Coatings that cure by oxidation are
97.
Amine blush is an amber oily film, which occurs on
98.
Oil-based coatings
99.
A pigment is
100.
The most important property of a primer for steel is its ability to
101.
“Kick-out” occurs when
102.
An epoxy ester coating is a one-package coating that cures by
Address: Suite 609 315 Lupita Unions, Ronnieburgh, MI 62697
Phone: +2424755286529
Job: District Education Designer
Hobby: Yoga, Gunsmithing, Singing, 3D printing, Nordic skating, Soapmaking, Juggling
Introduction: My name is Moshe Kshlerin, I am a gleaming, attractive, outstanding, pleasant, delightful, outstanding, famous person who loves writing and wants to share my knowledge and understanding with you.
We notice you're using an ad blocker
Without advertising income, we can't keep making this site awesome for you.
