NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. | Exams Nursing | Docsity (2024)

Download NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. and more Exams Nursing in PDF only on Docsity! NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Dew point is the temperature at which - Answer condensation occurs. You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: - Answer Document the problem and advise the Contractor and Owner's representative. If a contractor is using a poorly maintained compressor to supply air for abrasive blast cleaning and conventional airspray, the coating inspector should perform a - Answer blotter test for the presence of oil and water. Upon arrival of coating materials, the inspector should - Answer observe and document the amount of material and batch numbers. Relative humidity is - Answer a measure of the amount of moisture in the air compared to saturation level. Galvanic corrosion occurs on which of the following substrates? - Answer Metal NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. When applying Thermal Spray Coatings the specification is most likely to reference: - Answer SSPC-CS 23.00/AWS C2.23/NACE No. 12 What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT) gauge? - Answer 2.5 cm (1 inch) Polymerization is the process of? - Answer Monomers joining together. An exposed area of the substrate or previous coat of a conductive material, often caused by poor application technique is called: - Answer Holiday Checking is: - Answer a fine crack in the surface of a coating that rarely reaches the substrate. Inspection documentation is important because: - Answer Owners use the documentation for a variety of purposes. An Inspectors personal log book should contain: - Answer No comments regarding the application team. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. It is good practice for the NACE Inspector to have instrument calibration certificates available: - Answer At all times. In a non convertible coating the role of the primary solvent is to: - Answer To control the evaporation rate. Removal of weld splatter is required: - Answer When specifically identified in the owners specification. Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Off Dry Film Thickness(DFT) gauge include: - Answer Failing to determine the Base Metal Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky, or soft films. Conventional spray us good choice when: - Answer High quality finishes are required. Which of these tests uses a syringe? - Answer Bresle Patch NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Which one of these elements is not necessary for corrosion to occur: - Answer Reference Cell Digital hygrometers - Answer determine relative humidity, air temperature,and dew point temperature. Using SSPC Vis 1 as a guide when performing a visual inspection of a steel surface prior to surface preparation a NACE Inspector would assign which designations to the surface condition: - Answer Rust Grades A-D Inspectors daily reports are used: - Answer By the contractor to estimate the mount of work done that day, To provide continuity between inspectors, To aid in arbitration between the contractor and client, and To help in cases of a coating failure. Silicone coatings are typically: - Answer Applied in very thin films. Excess moisture during holiday testing can cause erroneous by creating a path across the surface of the coating to pinholes previously detected, or directly to the signal return connection. This is often referred to as? - Answer Telegraphing NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. ASTM Standards are applicable: - Answer When specified. The main responsibilities of the Inspector are to: - Answer Observe and report the quality of the work performed. When using a sling psychrometer a very large difference between the wet and dry bulb readings indicates: - Answer Low Relative Humidity The NACE Inspector should perform tests for soluble salts: - Answer When specified. Corrosion generally occurs at which of the following sites: - Answer Anode If Inspectors identify issues of non conformance during an inspection, they should: - Answer Inform both the Contractor and the inspectors supervisor so they can take appropriate corrective actions. You are the NACE Inspector on a job where ISO ST 3 has been specified. The Contractor normally works to SSPC standards and been referencing SSPC SP 3. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. The Inspector should record the serial numbers of inspection instruments: - Answer Each time the instrument is used. ISO SA 3 is directly equivalent to: - Answer NACE No.1/SSPC SP 5 On a blast cleaned surface, an ultraviolet light is generally used to detect: - Answer Grease and Oil You are the NACE Inspector on a job where NACE No.2/SSPC SP 10 has been specified. Your are finding the Contractor is leaving mill scale on the surface and as a result you have been rejecting the blast. The Contractor is very upset and has told you that the standard permits up to 5% of the mills scale to remain and still be in compliance with the standard. Your FIRST preferred course if action is to: - Answer Review the relevant standard with the Contractor. A successful coating Inspector must be able to: - Answer Look for problems and issues during application. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. A magnetic pull off type gauge is a good choice when: - Answer When an intrinsically safe tool is required. The Inspector's log book is generally: - Answer Retained by the inspector upon project completion. The most important factor resulting in improved job site safety is: - Answer Situational Awareness You are the NACE Inspector on a 5,000 sq ft job where SSPC PA 2 has been specified.Assuming all areas are in compliance, how many gauge readings and spot measurements are required? - Answer 225 gauge readings resulting in 75 spot measurements. Stripe coats are generally applied to: - Answer Edges, corners, welds and complex geometric shapes. SSPC SP 1 identifies the use of: - Answer A wide variety of materials. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Which one of the following documents is the best source for coating technical data: - Answer Technical Data Sheet Which is a component that supplies most of the features and functions of the material? - Answer Binder NACE Level 1 Inspectors have been trained to perform: - Answer Visual inspection and non destructive testing. If a Thermoset coating is heated it will: - Answer Harden and retain its hardness when cooled. As a NACE Coating Inspector your responsibility with respect to safety is to: - Answer Act in accordance with the site safety requirements and set an example. Prior to using Inspection tools the inspector must: - Answer Ensure the instrument is within calibration parameters, be trained on how to use the equipment and read the manufactures instructions. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Removal of surface contaminants is done by: - Answer A combination of methods. Common errors that can produce inaccurate readings when using Wet Film Thickness(WFT) gauges include: - Answer Using a damaged gauge and dragging gauge though wet coating. ISO ST 3 is described as: - Answer Very Thorough hand or power tool cleaning You are an Inspector on a project where SSPC SP3 is specified. What sort of tools should you expect the Contractor to use to achieve the standard? - Answer Power Tools The least effective method of surface cleaning is most likely: - Answer Hand Tool Cleaning Nace No. 4/SSPC SP 7 is a joint standard for: - Answer Brush Off Blast Cleaning Surface profiles describes: - Answer The level of surface roughness required after abrasive blasting. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. To be of value the Inspectors documentation must be: - Answer Timely, accurate and concise. A NACE Coating Inspector is permitted to transport coating material when: - Answer The Inspector should never transport coating material. Solvents are added to coating formulations to: - Answer Dissolve binders and form liquid coatings. (Also known as 'fisheyes' or 'crawling') is the term for surface breaks in the film that reveal the substrate. It is often a result of grease or oil contamination on the substrate. - Answer Cissing Which coating cures the fastest? - Answer Polyurea Amine blush is likely to occur with which type of coating? - Answer Epoxy Fusion Bond Epoxy(FBE) is most commonly used to coat which of the following? - Answer Pipe NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Which of the following coatings are co-reacting? - Answer Polyurethane and Epoxy Which of the following coatings may require external moisture to cure? - Answer Single component polyurethane and Solvent borne inorganic zinc. The requirements of coating project are defined by which of the following? - Answer Coatings Specifications A pre job conference is useful for discussions on which of the following? - Answer Safety, Cleaning, Application and Schedule. You are the Inspector on a project where specification level of cleaniness is "near white". Which standard would you follow? - Answer NACE No. 2/SSPC SP 10 The powerful standard for cleaning to bare metal with a minimum profile of 1 Mill (25.4microns) is: - Answer SSPC SP 11 Which profile comparators are referenced by ISO 8503? - Answer Grit and Shot NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Inspection records may be used to: - Answer Help resolving legal or arbitration disputes, Assist owners in the evaluation of the applicator performance, assist owners in the evaluation of the inspectors performance and determine total cost of project. Daily reports or weekly reports should be written in? - Answer Pen According to ASTM D 4417 Method B 2014 when taking measurements using a profile gauge, at each location you should make? - Answer 10 readings per location, recording the maximum value. Determine mean (average) for all maximum valises the reported profile. What is an advantage of airless spray compared to conventional air spray? - Answer Faster production rate You arrive to inspect a bride repainting project where containment (enclosure) has already been erected but dehumidification is not being used. What Inspection challenges do you expect specific to working inside the containment? - Answer Illumination and Control of temperature and humidity. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Improper atomization of the coating may cause which of the following? - Answer Uneven DFT, Dry Spray and Overspray. High viscosity due to low temperature should be corrected by? - Answer Adding extra thinner. SSPC Technology Guide No. 12 states coating inspection requires a minimum of which of the following? - Answer 50 foot candles (538 lumens) One major advantage of conventional spray? - Answer Applicator control. When using a wet film thickness (WFT) comb/gauge, the measurement should be taken? - Answer Immediately after the coating is applied. A well written specification requires a surface profile depth defined as? - Answer A range of measurements. The testing for water soluble ferrous salts is? - Answer Potassium Ferricyanide Test NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Solventborne inorganic zinc primer is being applied with airless spray to complex bride with difficult access for application. The contractor is having difficulty with hight DFT resulting in mkudcracking. What application method might be a good alternative? - Answer Conventional Spray When reporting the wet film thickness from a wet film thickness comb/gauge (WFT) you report? - Answer The last tooth that has coating on it. Adding an incorrect solvent to a coating may cause? - Answer Non drying and non curing. You are reviewing the documentation for a tank waiting project and notice there is a conflict between the project specification and the manufacture's product data sheet on the required DFT of the primer. The owner is not reachable for clarification. What should be done? - Answer Follow the specification. You know that you are sensitive to amines, but not polyamides. What document would you review prior to arriving on the joist to know whether amines will be used? - Answer The contractor's contract. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. You have a 10mil (254 micron) conductive coating on a nonconductive surface and need to check for holidays and discontinuities. How would you perform the inspection? - Answer Visually, you cannot use a holiday detector. According to NACE No.4/SSPC SP7, mill scale, rust, and paint are considered highly adherent if they cannot be removed by? - Answer Lifting with a dull putty knife. ISO8501 St 3 is the standard for which of the following? - Answer Very Thorough hand and power tool cleaning Which standard requires a "commercial grade" power tool cleanliness? - Answer SSPC SP 15 Grounding the pump and fluid hose used in airless spray: - Answer Prevents static sparking. As the Inspector called in to verify a blast, you find steel which has scattered highly adherent rust remaining on less than 5% of the unit area. Which standard has been achieved? - Answer NACE No. 2/SSPC SP 10 NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. Fisheyes (cissing) often resemble crater like breaks in the coating film that reveal tiny areas of substrate because of? - Answer Contamination such as grease, oil, or silicone. The contractor is required to perform this action: - Answer Shall The contractor has open choice on actions: - Answer May The contractor is strongly recommended but not required to perform this action: - Answer Should The owner is reasonable for performing the action: - Answer Will When an Inorganic Zinc Rich primer is applied too heavily a common result is? - Answer Mud Cracking Which SSPC VIS 1 rust grade defines a surface covered with both mill scale and rust? - Answer Grade B NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. ISO SA 2 1/2 is a blast cleaning standard that is similar to which joint standard? - Answer NACE No. 2/SSPC SP 10 Approximately 75% of premature coating failures are caused by? - Answer Inadequate or improper surface preparation. NACE SP0178 comparator addresses which of the following? - Answer Butt welds, Lap welds, Radius edges and Finishing grades of weld. You are on a project where Testex tape is specified to determine surface profile by ASTM D4417 Method C. Which of the following is likely to cause reading errors? - Answer Dust on the surface and Using an incorrect grade of tape. Which coating component forms a stable film that retains its characterstic properties? - Answer Binder/Resin A barrier coating interrupts the of the electrochemical cell? - Answer electrolyte Coatings adhere to a substrate by which of the following mechanisms? - Answer Polar, Chemical, and Mechanical. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. A decrease in temperature will generally cause the corrosrion rate to? - Answer Decrease The electrolyte is a medium which carries the following type of current? - Answer Ionic Corrosion occurring uniformly across a surface is called? - Answer General Corrosion When conflict occurs on a coating project, as the Inspector, the preferred first course of action is to? - Answer Actively listen and endeavor to understand the positions of others. A proper coating specification should contain information regarding which of the following? - Answer Surface preparation standards, safety and locations to be coated. According to the NACE attestation, when is it OK to accept a gift from a contractor? - Answer Never acceptable. NACE CIP 1 CBT EXAM PRACTICE QUESTIONS AND ANSWERS WELL DEFINED. What should you do if you find discrepancies between the specification and the coating manufacturers technical data sheet? - Answer Seek written clarification from the coating manufacturer. Which of the following are generally components of the inspection reports? - Answer Results of inspection tests, Location of work and Details of preparation and application. Inspection reports typically provide sufficient detail permitting the owner to evaluate? - Answer Contractors performance, inspectors performance, job progress and work interruptions. As an inspector headed to the joist for the first time, where would you always find instruction regarding appropriate types of Personal Protective Equipment(PPE). - Answer Safety Data Sheet(SDS, previously called MSDS The contractor should not use air blow off the surface of a coating if: - Answer Lead is present in the coating waste or blast debris. When inspecting a silicone coating it is very important to: - Answer observe application and ensure the field is applied at the correct DFT.